The following two tips to teach you how to prolong the service life of the drill bit, to hit plastic or cloth must be better bit, and to hit dozens of times, to hit a fat soap corner or candle to lubricate the inner wall of the drill bit, cooling the use of the drill bit.
一、使用过程，规避钻头断裂方法：
1、 The method of avoiding bit fracture is as follows
1、堵了一定要取下来清理干净-配合我们店里的捅针（很多客户堵住了还是直接打，这样就断了），
1. If it's blocked, you must take it down and clean it up - cooperate with the poke needle in our store (many customers still hit it directly, so it will break),
2、粘一点皂角，跟打纸一样打一下，里面就有了）再装上去用的，里面润滑作用！本产品试用于空
2. Stick a little bit of Gleditsia, just like playing paper, and you will have it inside) and then put it on it. It has lubricating effect inside! This product is used in the blank
心钻头，钻嘴。在打孔的时候感觉钻头压不下去，亲请先停下，涂抹点我们润滑剂在继续，有效的节约换钻
Drill bit, drill bit. When drilling, I feel that the drill bit can not be pressed down. Please stop first and apply some of our lubricant to continue to effectively save and replace the drill
头时间，节省更多成本。
Head time, save more cost.
二、使用过程，钻头正常使用方法：
2、 Operation process and normal use method of drill bit:
钻针使用时，纸张摆放要整齐、平整，不得弯曲或凹凸不平。机器动作时，要注意查看机器中其他部
When the drill needle is used, the paper should be placed in order and flat without bending or uneven. When the machine moves, pay attention to other parts of the machine
件间的配合、润滑情况。纸张摆放不合格或机器机器其他部件间配合、润滑不好时，容易堵针、断针或导致
The matching and lubrication between parts. When the paper is not placed properly or the coordination and lubrication between other parts of the machine are not good, it is easy to block the needle, break the needle or cause it
产品不合格。
The product is unqualified.
此外，钻孔时，已经打过的孔，不得重复再打，否则，钻孔不能形成圆形，针孔内也会因纸屑歪斜而 堵针或断裂。
In addition, when drilling, the hole that has been drilled should not be repeated, otherwise, the hole can not form a circle, and the needle hole will be blocked or broken due to paper scraps skew.
三、使用速度：
3、 Use speed:
①因针孔大小而定，针孔越小，下压杆进度应越慢。
① Depending on the size of the pinhole, the smaller the pinhole, the slower the progress of the pressing rod.
②下压杆下压速度要保持匀速，不得太快或太慢。太快时，钻针用力过猛，容易断针；太慢时，容易 使纸品变焦。
② The pressing speed of the down pressure bar should be kept uniform, not too fast or too slow. Too fast, too strong drill needle force, easy to break the needle; too slow, easy to make the paper zoom.
③待钻两孔间距离越小，速度越慢。
③ The smaller the distance between the two holes to be drilled, the slower the speed.
④钻针工作时，中途不能停顿，才能使钻孔废料彻底排出。此外，要注意在钻针连续使用几小时后，
④ When the drill needle is working, the drilling waste can be discharged completely without stopping. In addition, it should be noted that after several hours of continuous use of the drill needle,
及时替换，以免钻针在疲劳状态下继续工作。
Replace it in time, so as to avoid the drill needle continuing to work under fatigue condition.
四、钻孔材料如果是腹膜、上光纸品，钻孔时，更换待钻纸张时间的时间差不能太长，也不能等钻针冷却后
4、 If the drilling material is peritoneal or glossing paper, the time difference between the time of replacing the paper to be drilled should not be too long or wait for the drill needle to cool down
再行钻孔：因为钻针在工作之后，膜或油会冷凝在针孔内，从而导致排料困难。为防止堵针，必须用胶版纸
Drilling again: because the film or oil will condense in the pinhole after the drill needle is working, which leads to difficulty in discharging. In order to prevent needle blocking, offset paper must be used
做钻孔材料，来排掉残留在孔内的废料，在钻针休息前完成，这一工作尤为重要。
It is very important to make drilling materials to discharge the waste materials left in the hole before the drill needle rest.
五、待钻纸张叠加总厚度：以钻针长度及钻纸张材料而定。分别为：胶版纸叠加总厚度应为针长80%，铜 版纸或原纸为60%，腹膜或上光纸为40%以下
5、 Total stack thickness of the paper to be drilled: depends on the length of the drill needle and the material of the drilling paper. They are as follows: the total superimposed thickness of offset paper should be 80% of needle length, 60% of coated paper or base paper, and less than 40% of peritoneal or glossing paper
六、钻针上不得使用任何润滑剂，以免阻碍钻孔废料的排出（好使用蜡烛当做润滑剂）。钻针使用时如有
6、 Do not use any lubricant on the drill needle to prevent the discharge of drilling waste (use candle as lubricant). When using drill needle, if any
杂音，并再堵塞现象，可用蜡烛擦放在针口上，由于钻头在工作时会发热，使蜡烛融化，并顺针管向上流
In case of noise and blockage, the candle can be wiped on the needle mouth with a candle. As the drill bit will be heated during operation, the candle will melt and flow upward along the needle tube
动，于此同时，钻孔废料也随蜡烛油的上流而排出（注意：此方法只在钻针发热、发烫时使用）。
At the same time, drilling waste is also discharged with the upward flow of candle oil (Note: this method is only used when the drill needle is hot and hot).
塑料袋打孔：打孔机不单单只能打纸的哦，PVC-PP塑料袋子都能轻松
Plastic bag punching: punching machine can not only punch paper, but also PVC-PP plastic bag
打孔
Drilling
布料打孔：打孔机不单单只能打纸的哦，无纺布
Fabric punching: punching machine is not only used to punch paper, but also non-woven fabric
联系人：李女士
Contact person: Ms. Li
手 机：13587588683
Mobile phone: 13587588683
邮 箱：49576771@QQ.com
Email: 49576771@QQ.com
